After Setting Up Gospas Hottub Will It Repeat the Cycle and Strart Again
Helpful Links
Operational & Technical Bug
Why is my spa overheating?
If the spa is located in an area that is experiencing hot weather, it is normal to have the spa h2o temperature rise.
To help go along your spa cooler, adjust the spa's filtration cycles to no more three hours per mean solar day, and only one 60 minutes per day during the warmer summertime months. Set the cycles to run during afterward evening or early morning time hours when the outside air temperature is libation. During the summer, gear up merely ane filter cycle per mean solar day.
Open the cover for several minutes, long enough to allow the water to absurd down. Repeat a couple times weekly as necessary. For safety reasons, never leave your spa unattended with the cover open.
If OHH is displayed on the control panel, this means that the thermometer has detected spa h2o temperature above 110 degrees F. Do not utilize the spa at this temperature. Take the advised steps in a higher place to cool your spa water to below 106 degrees F before use.
Why won't my spa heat?
If your spa temperature is low, first check the thermostat to see if information technology has been turned down or ready to depression rut range. Adjust the thermostat to desired temperature or ready to high estrus range.
Some other common reason for your spa temperature to be low is because the loftier limit sensor has tripped. Printing any push button on your control console to reset the system.
If neither of the higher up steps works, your heating organisation may be lacking. Contact your authorized Bullfrog Spas Dealer for further diagnosis.
Why is my GFCI breaker tripping?
Warning: You must be a qualitied electrician and or service technician to perform diagnosing or serial injury or death tin can upshot: High voltage components are in apply.
If the spa was recently installed, the well-nigh mutual reason the GFCI would trip is the Load Neutral (white wire) between the spa and GFCI which must exist connected to the Load Neutral port in the GFCI breaker. If the neutral wire is continued to the neutral busbar, the breaker will trip during startup. The neutral connexion must not have contact to the ground on the load side of the breaker or it volition trip.
If the spa is not tripping immediately upon startup, a process of elimination should be used to place the problem. Disconnect 1 component at a time from the control board and try restarting the spa. If the breaker trips, reconnect the component so attempt over again by disconnecting a different component. Continue repeating this process until the billow does not trip. Components include pumps, heaters, lights, stereos, ozone, etc. If the breaker does not trip after disconnecting the component, and so the disconnected component is the source of the problem. In one case you take determined which component is at fault, supplant the component.
If you have non establish the source of the problem afterward disconnecting each spa component individually, disconnect all components from the control board and try starting the spa. If the breaker however trips, a certified electrician will need to audit the breaker and wiring.
Why is my spa making a vibration noise?
A light vibration noise is normal while the spa pumps and motors are running.
If your spa'due south vibration racket level seems excessive, the first thing to bank check for is the spa motor'south shipping bolts. Each spa motor has a shipping bolt that can contribute to the vibrating noise and can be removed one time your spa is delivered and installed. The bolts have tags with blood-red lettering for easy identification.
If the bolts take been removed and your spa even so makes an excessive vibration noise, contact your spa dealer for further assistance.
Why is my spa pump creating a called-for smell or making excessive noise?
If your spa pump is creating a burning smell or making excessive noise, the pump motor is defective. This tin happen when running the pump during high ambient outside temperatures or due to excessive run times. Delight contact your authorized Bullfrog Spas dealer for replacing the pump.
Why are my command pad and spa equipment not operating?
If your hot tub control pad and spa equipment are not operating, that means yous have no electric ability to the spa. Turn on or reset the GFCI circuit billow to supply the spa with ability again. If this does non solve the problem, have a qualified Electrician check the electrical service for bug.
Another reason your command pad and equipment won't work is if the fuse (20 or 30A depending on the system) has blown. Contact your authorized Bullfrog Spas Dealer for repair/replacement.
Why are my hot tub jets non working?
If your hot tub jets are s urg ing on and off , the first thing to bank check is your water level as it might be too low. Arrange water to the water level indication mark on the faceplate of the filter assembly.
Next, check your filters as they may be dingy. If so, clean or replace them .
If your spa's jets seem weak or are not working, beginning double-check to make sure that the valves are open up. JetPaks accept valves at the bottom that open and close past turning the valve . Adjustable jets on One thousand Serial, A Serial, R Series, and STIL spas open up and shut by turning the jet confront. Adjustable jets on Ten Series spas open and close by turning the outer ring.
The next affair to check is the suction fitting(s) ordinarily located at the bottom of your spa vanquish to see if they are blocked. Remove whatsoever debris you find by hand or with a spa vacuum.
If your jets are not working after filling your spa, you almost probable have an airlock in the pump. Follow the directions in the "how practice I fix an airlock in the pump" section below.
Why won't my spa won't work after draining and refilling it?
If your spa pumps/jets are not working after filling your spa, you most likely have an airlock in the pumps. Follow the directions in the "how do I fix an airlock in the pump" section beneath.
How practise I fix an airlock in the pump?
To prevent airlocks when filling your spa, be sure to open up all valves in the JetPaks and all other jets in the spa before filling to let as much air every bit possible to escape from the system during the filling process. Fill your spa through the filter by taking the filter cap off and put the hose straight in the filter. Detailed instructions for filling each spa serial are found in your owner'southward manual.
Your hot tub's pumps must exist primed directly after filling to ensure correct functioning of your spa and get rid of any airlocks. Later on initial startup, verify that the abode status screen appears on the panel.
Depending on your spa model, your spa has either i,ii, or iii pumps. To prime number the pumps, printing the "Jets i" button once to prime in low-speed. After the pump turns on and water is visibly flowing from the jets wait a few seconds and then press "Jets 1" once more to initiate highspeed operation of Pump ane. The pump has primed when water is flowing from the jets.
If your spa is equipped with a second jet pump, repeat the priming process for Pump 2 by pressing the "Jets two" button in one case to plough on low speed and then a 2d time to plow Pump ii on loftier.
If your spa has a 3rd pump, press the "Jets 3" button to prime number the third jet pump. All pumps will have primed when water is observed flowing from the jets associated with each pump.
On rare occasions, priming the pumps volition not go rid of an airlock. The next step is to remove the front panel and locate the pump with an airlock. The wet-end of the pump has a bleed valve—loosen this until all the air escapes and water starts to drip out, or loosen the wedlock on the pump to allow the air out until you see h2o. Practise not attempt this while the spa pump is running. If you need help doing this or this does non resolve the trouble, please contact your authorized Bullfrog Spa Dealer.
Why practice my spa jets turn off during performance?
If your jets plough off automatically afterwards either 30 or sixty minutes, this is completely normal. The automated timer has completed its cycle. Simply turn the pump dorsum on to start a new cycle.
Another reason your jets can plough off unexpectedly is if the pump has overheated due to the vents on the equipment door being blocked. Articulate abroad whatsoever items from the vents and wait a while to see if your jets work over again.
The terminal reason your spa jets tin turn off is if the pump motor is lacking. In this instance, contact your authorized Bullfrog Spas dealer for service.
Why are my hot tub jets/pump not turning off?
If you are trying to turn off the pump for jets 1 on your spa and it appears that they are not turning off, your spa is in the eye of a filtration wheel. Spas non equipped with a dedicated filtration pump volition plough on automatically, using jet pump 1 on low speed, to filter and/or estrus. This is normal spa operation.
What exercise I do if my spa is leaking?
If you lot notice your spa is losing h2o, bank check all fittings and equipment in the equipment compartment for the source of leakage. If a leak is detected, tighten the fitting past hand. If the leak persists, you cannot find the source of the leak, or the leak is coming from the shell, contact your authorized Bullfrog Spas Dealer.
Water Quality Bug
How do I get rid of green water in my hot tub?
The offset reason why your hot tub can turn dark-green is from algae growing in the spa. This happens because of a lack of sanitizer (chlorine or bromine). Super sanitize (shock) the spa water to become rid of algae and other growth in the spa.
If the spa water has had algae growing for as well long of a fourth dimension, shocking the spa h2o may not exist enough. At that point, you would want to drain your spa, give it a expert cleaning, and refill your spa. Be certain to properly maintain your spa pH and sanitizer levels going frontwards to prevent future algae growth.
A second reason why hot tub water can appear green is from metals and minerals in the water (unremarkably copper). Check with your spa dealer almost local water conditions to see if your area has copper in the ground h2o. If this is the instance, your dealer will be able to provide custom tips for keeping your spa water clean and articulate.
How practise I get rid of mold in my hot tub?
Mold, mildew, and fungus like to grow in warm, damp places. The starting time step in preventing these from growing in your spa is to maintain your spa water. Y'all should add sanitizer post-obit every utilise.
It'south too of import to regularly clean all surfaces on and effectually your spa, including the encompass (the underside and the tiptop), cup holders, headrests, etc. Nosotros recommend cleaning those surfaces every 30-45 days.
Why is my spa water cloudy?
Cloudy spa water is commonly caused by non-filterable liquid waste matter (e.k. perspiration) and a lack of proper maintenance. Get-go, bank check your spa's pH level and adjust if needed. Loftier pH levels are a common cause cloudy water.
Next, test your sanitizer (chlorine or bromine) levels. If the sanitizer level is too depression, add more. Wait two hours and test the water again. Add more sanitizer as necessary so look two more hours. Repeat this process until the sanitizer levels consistently read correctly. Ever run the pumps for fifteen minutes with the cover open after adding whatever chemicals.
If you are using the FROG @ease for Bullfrog Spas water care system, first make sure the SmartChlor cartridge is not empty. Supplant the cartridge if necessary. If it is not empty, plow the dial setting up 1 number and monitor chlorine levels for a few days while maintaining water balance. If needed, turn the dial up once again. The entire FROG @ease System including a FROG @ease Mineral Cartridge needs to be replaced every four months. Without the minerals, SmartChlor will not be enough to sanitize the hot tub.
If your sanitizer levels are generally testing at right levels and your spa water is nevertheless cloudy, you tin increment filtration times to come across if that helps.
You may also desire to make clean or replace the filters if y'all have not done so recently.
Non-filterable micro-particulate waste (eastward.g. dust) tin likewise contaminate the water leading to cloudy water. To remove these substances, use a water clarifier product as per the manufacturer'south instructions.
How do I get rid of foam/bubbles in my hot tub?
People and their swimwear introduce virtually of the unwanted contaminants that crusade cream and bubbles in a hot tub. To reduce the corporeality of foam and contaminants introduced to your spa water:
- As much as possible, avoid entering your spa with sunscreen, lotions, deodorants, shampoos, or similar substances on your trunk, or detergents on your clothes.
- Do not wash swimwear you intend to wear in your spa with detergents. Many people go on a dedicated "spa" suit that is never laundered with detergent but but rinsed well later on use.
- Rinse off in the shower before (and after) spa use.
For a temporary fix for cream and bubbles in your spa, add together an anti-foam or foam remover as per the manufacturer'southward instructions. This will get rid of the cream almost immediately but will simply be temporary, lasting a twenty-four hours or two.
The best style to control foam is to super sanitize (shock) the water. This will destroy the soap agents that normal levels of sanitizer volition non. Make sure to properly maintain your spa pH and sanitizer levels and avoid introducing the unwanted contaminants listed in a higher place to preclude future foam and bubbles.
How exercise I preclude a yellow water line from building in my spa?
With normal use of the spa, oils, lotions, and hair products can build up on the surface of the water in small amounts. This could get out a yellow water line around the perimeter. This buildup can be hands removed using a spa surface cleaner or its equivalent. Avoid using cleaning agents that leave lather residue in the water.
Warning: Never allow your spa surface to exist exposed to alcohol, acetone (nail smooth remover), boom polish, dry cleaning solution, lacquer thinners, gasoline, pine oil, abrasive cleaners, or whatsoever other household chemicals other than those listed. These chemicals void the warranty.
What do I practise if my pare is sensitive to hot tub chemicals?
If your skin is sensitive to hot tub chemicals, make sure to rinse off later you get out of the spa. Using lotions to moisturize your skin can also help.
It'south besides of import to making sure the pH and sanitizer levels are correct in your hot tub. Low pH levels (less than 7.iv) can crusade discomfort to your pare and as well equally corrosion to the spa equipment. To increase pH levels, add a pH increaser.
If your sanitizer levels are correct and you yet experience discomfort, try switching to a different sanitizing agent—If you are using chlorine, try bromine, and vice versa.
Your dealer may have additional tips based on the chemical makeup of your local water supply. Whatever allergic reactions should exist treated past a medical professional.
How practice I get rid of debris in my spa water?
Droppings from wind, trees, and users will occasionally accumulate on the bottom of the spa. The filtration system will remove the smaller debris. Large or heavy debris can be removed with a manus-held spa vacuum available at your Bullfrog Spas dealer.
Hot Tub Parts & Accessories
Where exercise I find replacement parts and accessories for my hot tub?
If y'all are in need of replacement parts or accessories for your Bullfrog Spa, first reach out to your local dealer.
Additionally, some products are bachelor online at store.bullfrogspas.com
Why are my spa headrests disintegrating?
Headrest discoloration and/or degradation is accelerated by high sanitizer use and improper ventilation subsequently shock treatments. To prevent your spa headrests from disintegrating, remove the them during and after stupor treating the spa water or when sanitizer levels are high. In addition, exit your spa cover open for at to the lowest degree 30 minutes after shocking to ensure the headrests are non afflicted.
It'south likewise a good idea to open the cover for merely a few minutes a couple times a week even if your spa is non being used or lightly used then that the excess chemical gasses building up under the cover can escape.
Nosotros also recommend regularly cleaning all pillows with mild soap, water, and a clean material. Monthly, care for the pillows using a non-petroleum-based product such every bit 303 Protectant. This will maintain h2o resistance and luster of the product.
How practise I replace my hot tub comprehend clips?
Broken clips are from stiff winds or failure to undo them earlier opening the cover and is not a warranty part.
Contact your dealer to get replacement clips or purchase them from our online shop.
To replace the embrace clip, first remove the male end of the clip. And then, use clippers to make ii small diagonal cuts on the clip loop. This makes an opening for the encompass loop. Insert the cover loop into the opening and button the encompass loop entirely into the clip.
Why can't I get a wifi signal on my hot tub?
If y'all tin't get a wifi signal on your Bullfrog Spa, first ensure that both the master and partner units are correctly installed. The primary unit should be continued to the spa's control board and the partner unit of measurement to the wifi router. If at that place is a solid bluish light on both units, then the connection is nowadays. If 1 or both of the units does not have a low-cal, or the low-cal is flashing, refer to the Gecko wifi troubleshooting website.
Why tin't I get a bluetooth indicate on my hot tub?
First, make certain the in.stream2 unit is turned on from the topside control panel.
Next, endeavor adjusting the stereo settings to zero (or to center).
If there is no power coming from the motherboard, the control box volition need to exist replaced.
If in that location is power coming from the motherboard but the in.stream2 will non plough on, the in.stream2 unit will need to be replaced.
Control Panel Mistake Code Questions
My spa has a Freeze Mode mistake code, what do I do?
Your spa is equipped with a freeze protection mode. When potentially freezing outside temperatures are detected, your command organization will turn on to check the water temperature. If heating is necessary to protect your spa from freezing conditions, your spa may turn on and heat to a prophylactic temperature. A notification will brandish on the main control screen indicating this fashion is engaged. If your spa shows this mistake lawmaking for more than 24 hours, contact your dealer for further diagnosis.
My spa has a Low Menses / Heater Overheating fault lawmaking, what practice I practice?
First, remove the filters and attempt running the spa without them. Make sure the area is clear of debris. Turn the pumps on and off several times each to try purging out any airlocks in the pumps.
Side by side, check for blockage in the pumps. To do so, turn the spa off and bleed the spa. Disconnect the intake side of the pump and check inside for blockages. Spa accessories such as a scumball, leaves, or other droppings tin can be sucked into the pumps and need to be cleared away.
To ameliorate prevent future blockages, make certain yous are using genuine Bullfrog Spas filters equally other filters may non prevent debris from entering the pumps.
If the h2o flow is good and there is still a menses condition lawmaking, the sensors on the heater should be tested. The heater may need to be replaced due to a bad sensor. If the upshot nonetheless persists, the circuit lath will demand to be replaced.
If the spa is new, check to ensure the power cord is connected properly. In addition, check the power connections to the pump. Finally, check the control set up for proper performance (refer to dealer).
What does filtration suspended mean?
This lawmaking does not bespeak an error, it indicates that the spa filtration wheel has been suspended because a user activated the spa while it was performing a filtration bicycle. No further action is required. The side by side regularly scheduled filtration wheel will occur.
What is a purge period?
In order to maintain sanitary atmospheric condition and protect against freezing, your spas pumps volition purge water from their respective plumbing past running all pumps at the beginning of each filter cycle.
The filtration schedule shown on the screen volition apply to the principal filtration pump. If your spa uses a apportionment pump configured to run 24 hours, the screen volition show y'all the purge setting instead of filtration. The purges are pre-programmed for a fixed number of minutes; therefore, the elapsing will be ready to Due north/A on the screen, and just the start fourth dimension can exist modified.
Other Ofttimes Asked Questions
What do I do if I won't be using my hot tub for a long period or during holiday?
2-vi weeks of unuse
If the spa volition non be used for at least two weeks, lower the temperature to the lowest setting of lxxx F (26°C) or identify in depression range heat fashion. Lowering the temperature volition cut the cost of operation; however, you volition need to adjust the temperature setting approximately 4 hours before apply in order to oestrus the spa to 100 F (38°C).
Fifty-fifty though yous will not be using the spa, exist sure to maintain the spa water and frequently check that the spa is operation correctly. Failure to do and then could lead to corrosion, staining, or scaling to the spa and its equipment.
During periods of freezing temperatures, a spa that has malfunctioned may be subject to damaged plumbing or equipment as a effect of ice buildup within the spa. If the spa cannot be checked and maintained on a weekly basis, then consider winterizing the spa.
More half dozen weeks of unuse
When you lot are not planning to use the spa for half dozen or more weeks, or when someone is non able to maintain the spa on a weekly basis, y'all should use Away fashion. For extended absences you may besides choose to winterize the spa.
How do I winterize my hot tub?
Bullfrog Spas are designed to office well, stay warm, and hold upwards through the coldest of weather and exercise non require winterization unless yous will be leaving your spa unattended for 6 or more weeks.
Either way, we recommend to check-in on your spa weekly during winter months to aid prevent freeze damage.
To winterize your Bullfrog Spa, follow the detailed instructions in this article:
https://www.bullfrogspas.com/blog/how-to-winterize-a-hot-tub/
Can I fill a spa in freezing winter temperatures?
If your spa is beingness delivered during the winter or y'all demand to drain and refill your spa during freezing temperatures, you may exist wondering if the cold weather mean y'all can't fill your spa with water.
Luckily, you can make full your spa in freezing wintertime temperatures. To keep your spa components safe from the cold, but turn your spa on as soon as it is full so the heater and pumps continue everything from freezing.
Sometimes, your dealer may postpone delivery of your spa during winter storms because it tin can exist dangerous for them to evangelize a heavy spa with snowfall, rain, or ice on the ground. One time it is condom again, they will deliver your spa and can help you fill it up and get it started.
If yous don't plan on using your spa during the winter, follow this guide on winterizing your hot tub. However, using a hot tub in the winter is considered the most enjoyable time by many spa owners.
What do I exercise when my spa loses power in freezing temperatures?
If your Bullfrog Spa loses power during freezing temperatures either due to a power outage or a malfunction and the GFCI won't reset, yous will want to help go on the spa and its components warm until power is restored or your dealer can repair the malfunction.
Practice non bleed your spa. Get out your cover on to retain as much heat as possible.
Remove the admission panel to your spa and place a small space heater inside the cabinet on a low setting. This will help keep the pumps and pipes warm. Y'all can also place a blanket over the equipment area to help keep everything insulated.
Frequently monitor the spa until power is restored and your spa is operation once more.
How do I move my spa?
A cart or dolly that can back up at least 900 pounds is the all-time way to move your spa. Sideslip sheets or carpets tin can also be used to elevate a spa on about surfaces.
Spas can exist moved in the horizontal or vertical position, but do not lift the spa on the door side because the door side cannot support the weight of the spa and yous may suspension the door.
Be careful of common obstacles in your path such equally overhanging tree limbs, awnings, protruding gas meters, water meters, and A/C units.
Which filter wheel (water intendance operation manner) should I utilise for my spa?
*The following information is for Bullfrog Spas model years 2019 and newer. Please refer to owner's manual for your spa for the well-nigh accurate information.
The best filter cycle for your situation will depend on how often yous use the spa and what time of day you typically use the spa. The 2 almost common modes are Standard-beginner and Super Energy Savings. The manufacturing plant default setting is Super Energy Saver mode.
In the descriptions of each mode below, "economy way" ways that the ready point will exist reduced past 20°F* (11°C), which ways that the heating system will not be engaged unless the temperature falls to 20°F (11°C) beneath the spa's gear up temperature. The filtration schedule shown on the screen will utilize to the main filtration pump. If your spa uses a circulation pump configured to run 24 hours, the screen volition prove you the purge setting instead of filtration. The purges are pre-programmed for a fixed number of minutes; therefore, the duration will exist ready to Northward/A on the screen, and only the commencement fourth dimension can be modified.
Away
In Away mode, the spa temperature ready point will be reduced past twenty°F (11°C) (come across description of "Economic system mode" higher up). Spa will remain in Economy mode at all times of the day and all days of the week.
Suggested use: Use when on vacation or non using the spa for longer than 2 weeks.
Economy fourth dimension: Every day of the week, 24 hours per day.
Filter cycle start time: 8:00 PM, duration 3 hours.
Standard-beginner
In Standard mode, the spa volition oestrus to the set point and filter according to the spa'south standard configuration. Spa will estrus to set up indicate at all times and all days of the week. This is the default setting on new spas.
Suggested utilise: Use to maintain readiness for employ every day at all times of day.
Economy time: Will not utilize Economic system fashion.
Filter wheel start times: eight:00 AM, duration one.five hours and 8:00 PM, duration 1.five hours.
Energy Savings
In Energy Savings mode, the spa temperature set point will be reduced by 20°F (11°C) (see description of "Economy mode" above) during peak daytime hours. Spa volition heat to normal set point during evening hours and on the weekend.
Suggested utilise: Apply to relieve energy during weekday daytime hours and brand prepare for use at nighttime and all day on weekends.
Economy time: Monday – Friday, half-dozen:00 AM – 6:00 PM.
Filter cycle kickoff time: 7:00 PM, duration 3 hours.
Super Energy Savings (factory default setting)
In Super Energy Savings mode, the spa temperature gear up point will be reduced by 20°F (eleven°C) (see description of "Economic system mode" above) during meridian daytime hours. Spa will oestrus to normal set point during evening hours, every day of the week.
Suggested utilise: Use to salve maximum energy and heat only during set filter cycles.
Economy time: Volition non use Economy mode, only heats during filtration cycles.
Filter cycle kickoff fourth dimension: viii:00 AM, duration 1.5 hours and 8:00 PM, duration i.five hours.
Weekender
In Weekender mode, the spa temperature set up point volition be reduced past 20°F (11°C) (see description of "Economy mode" in a higher place) from Monday to Fri. Spa will heat to ready point at all times on the weekend (Sabbatum & Sunday).
Suggested apply: Employ when spa is used but on weekends and non on weekdays.
Economic system time: Mon – Friday, 24 hours per mean solar day.
Filter cycle start time: 8:00 AM, elapsing 1.5 hours and 8:00 PM, elapsing 1.v hours.
Default Settings: The Default Settings option will restore all Water Care modes and schedules to the spa's default settings. You will be asked to confirm your choice.
Note: Spas Non equipped with a dedicated filtration pump volition plow on automatically, using jet pump 1 on low speed, to filter and/or heat. This is normal spa functioning.
How do I drain my spa?
Step 1: Turn-off the main electrical breaker to spa.
Step 2: Locate the bleed below the equipment compartment door.
Pace 3: Pull the bleed out with a slight clockwise turn. Use pliers if needed. The drain is fully extended at approximately ii inches (5 centimeters).
Step 4: Remove drain cap. The bleed spout will not drain when fully extended.
Pace 5: Attach a standard garden hose. Push the bleed spout in halfway to actuate the drain. The Spa will drain about 5 gallons (twenty liters) per minute. Ensure that the drainage is in an surface area safely away from window wells or basement entries.
Step vi: Once the spa is fully drained, pull the drain spout out all the way, remove the hose, supervene upon the drain cap, and push the drain in all the manner.
How practice I remove and supervene upon my spa equipment door?
M Series Door Removal
Step 1: Remove trim strips from trim channels by pulling carefully and firmly, working from the bottom of the trim strip to the elevation. Identify trim strips aside.
Step 2: Remove door – Carefully pull bottom of door out toward you. Carefully catch the bottom corner of the door and pull it out plenty that y'all can slip your other manus in behind the side of the door about 4-5 inches (10-13 cm) up from the bottom. From there you will pull the door firmly away from the spa until the snap on the door pulls out of the snap feature in the rib. Continue to pull the door away until the second snap on the other side pulls out. The door tin then be dropped out of the groove on top and removed from the spa.
Stride 3: Electrical Disconnect – be sure to disconnect any lighting or whatever other electrical wiring that is mounted onto the door before completely removing it.
Step 4: When removed, lean door against spa. To reinstall spa door, opposite the instructions in a higher place.
M Serial Door Installation
Step i: Electric – Reconnect whatsoever lighting or electrical devices on the door before installing.
Step ii: Door – Slip the upper lip of the door into the superlative behind the lip of the spa. Lower the door while gently pushing on it until y'all feel the snaps line up with the snap features in the ribs. Starting from one side, force the offset snap into place and then force the other side until the door is secured.
Stride iii: Supercede trim strips by snapping each advisedly into the trim channel
STIL Door Removal
STIL spas are designed then that there are no visible fasteners from the exterior. Snap features in the corners and the cabinet panels allow for simple equipment area access, however, it is important to follow these recommended door removal instructions to avert damaging the door or corner panels.
Stride 1: Remove Corners – It is of import to remove the front two corners overlapping the door before attempting to remove the door itself. This is washed by placing a curt flathead screwdriver beneath the corner and slipping it up partway behind the corner and using information technology as a lever to pry out the bottom half of the corner outward. One time this is done, grab the corner by the lesser and pull information technology straight out allowing the superlative snap to come gratuitous. Pull corner down and out of the groove on the top.
Step 2: Remove Door – Once both front corners are removed, expect on each side of the front door to run across the snap feature congenital into the cabinet. To remove the door, start by placing a longer flathead screwdriver or curt pry bar into the middle of the snap feature and use it every bit a lever to pop the door out of the first snap. Catch the base of the door and carefully begin pulling it out such that the rest of the snaps come free 1 past ane beyond the length of the door. The door tin can so be dropped out of the groove on height and removed from the spa.
Stride 3: Electric Disconnect – exist sure to disconnect whatever lighting or any other electrical wiring that is mounted onto the door before completely removing it.
STIL Door Installation
Step 1: Electrical –Reconnect any lighting or electric devices on the door before installing.
Step 2: Door – Skid the upper lip of the door into the pinnacle groove of the extrusion. Lower the door while gently pushing on it until you feel the snaps line up with the snap features in the ribs. Starting from i side, forcefulness the get-go snap into place. Go on down the length of the door and forcefully push the cabinet into each of the snaps until the door is completely in and secured. You can experience along the bottom to make sure all are in place and no gaps are present.
Step 3: Corner – Slip the upper lip of the corner into the top groove of the spa. Starting from the height strength the starting time snap into identify, if the corner has slipped downwardly and is not affluent with the top groove this is the all-time time to push button information technology support into place. Continue downwards the length of the corner and forcefully push it into each of the snaps until the corner is completely secured. The corner should fit tightly against the cabinet on both sides.
A, R, & 10 Series Door Removal
Step 1: Remove trim strips from trim channels past pulling carefully and firmly, working from the bottom of the trim strip to the top. Place trim strips aside.
Stride two: Remove door – Carefully pull bottom of door out toward you lot. Carefully grab the bottom corner of the door and pull it out enough that you lot tin slip your other hand in behind the side of the door about iv-5 inches (ten-xiii cm) up from the lesser. From there you lot will pull the door firmly away from the spa until the snap on the door pulls out of the snap feature in the rib. Proceed to pull the door abroad until the 2d snap on the other side pulls out. The door tin so be dropped out of the groove on top and removed from the spa.
Stride 3: Electrical Disconnect – be sure to disconnect any lighting or whatsoever other electric wiring that is mounted onto the door earlier completely removing information technology.
Step 4: When removed, lean door against spa. To reinstall spa door, contrary the instructions higher up.
A, R, & Ten Serial Door Installation
Step i: Electrical – Reconnect any lighting or electric devices on the door earlier installing.
Step ii: Door – Slip the upper lip of the door into the top behind the lip of the spa. Lower the door while gently pushing on it until you feel the snaps line up with the snap features in the ribs. Starting from one side, forcefulness the get-go snap into identify and then force the other side until the door is secured.
Pace three: Replace trim strips past snapping each advisedly into the trim channel.
X6R Door Removal
Step 1: Remove trim strips from trim channels by pulling carefully and firmly, working from the bottom of the trim strip to the top. Place trim strips aside.
Stride 2: Remove door – Pull the bottom of the door forward, the door can so exist dropped out of the groove on top and removed from the spa.
Pace 3: Electrical Disconnect – exist certain to disconnect any lighting or any other electrical wiring that is mounted onto the door before completely removing information technology.
Step iv: Subsequently the door has been completely removed, lean door against spa.
X6R Door Installation
Step one: Electrical –Reconnect whatsoever lighting or electrical devices on the door before installing.
Step 2: Door – Sideslip the upper lip of the door behind the lip of the spa. Identify door deeply against spa flush with the side panels.
Step 3: Supercede trim strips by snapping each carefully into the trim channel.
Additional Resources
Source: https://www.bullfrogspas.com/frequently-asked-questions/
Post a Comment for "After Setting Up Gospas Hottub Will It Repeat the Cycle and Strart Again"